Extra Resources and Free Software Tools: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| (46 intermediate revisions by 7 users not shown) | |||
| Line 1: | Line 1: | ||
==CCP Master Blocks for MotoHawk== | ==CCP Master Blocks for MotoHawk== | ||
: | :'''[http://www.neweagle.net/support/wiki/docs/Other/CANResources/CCPBlockset/CCPBlockset.zip CCP Master Blocks for MotoHawk Version 1.0.0 Beta 6]''' | ||
Beta release of the CCP Master Blocks for MotoHawk, supporting MATLAB 6.5.1 through MATLAB R2008a | |||
Requirements: MotoHawk 2008a or later, .NET 2.0 Framework | |||
==MotoTron Other Documents== | ==MotoTron Other Documents== | ||
| Line 8: | Line 9: | ||
=== Programming and Development Wiring Harness === | === Programming and Development Wiring Harness === | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/QuickProgrammingHarness112.pdf 112 Quick Programming Harness]''' | ||
: '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/HARNP112002_Rev03_DevHarness_PCM09xx.pdf 112 Development Harness]''' | |||
=== SmartCraft 4- and 6-Port Hub Wiring === | |||
: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/SC_CONN_Pinout.pdf Junction Box Pin Out]''' | |||
: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_wiring3.jpg Junction Box Wiring]''' | |||
: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_internal2.jpg Junction Box Internal Circuitry]''' | |||
: | === Hard Boot Recovery === | ||
: '''[http://www.neweagle.net/support/wiki/docs/Other/48HardBootRecovery/Fire48HardbootRecoveryDocument.pdf Hard Boot Recovery Procedure for 48-Pin Modules]''' | |||
=== | ===3D CAD Models=== | ||
:: | :'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM24.ZIP ECM24 3D Model]''' | ||
:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM48.ZIP ECM48 3D Model]''' | |||
:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM112.zip ECM112 3D Model]''' | |||
:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM128.ZIP ECM128 3D Model]''' | |||
==KAntrak Software== | |||
: | :'''[http://www.neweagle.net/support/wiki/docs/CANtrak/CCDM_PC_Tool_(v1.0.6).msi CCDM PC Tool Installer]''' | ||
==Free Software Tools== | |||
=== | ===MotoHawk Scanner=== | ||
: | The MotoHawk Scanner is a useful tool when you have to work with a module with unknown programming. Instead of guessing the city ID until finding one that works or using a boot key to reflash the module, you can just use the MotoHawk Scanner to determine which city ID the module is on, then interact with it in MotoService or MotoTune using that city ID. | ||
'''To use this tool, make sure the following are completed:''' | |||
*''The Kvaser CAN-to-USB hardware is plugged into your PC, and your PC recognizes the hardware.'' | |||
*''The CAN network has a proper termination resistor between the two CAN lines (120Ω).'' | |||
*''The controller is turned on (battery power and/or key switch) and has proper CAN connection.'' | |||
When using MotoHawk Scanner make sure no other programs are using the CAN bus, for example Mototune or Kvaser CANKing. If another program besides MotoHawk Scanner is on the bus, the scanner might not work. | |||
: | :'''[http://neweagle.net/support/wiki/docs/Extra_Resources/MotoHawk%20Scanner.exe MotoHawk Scanner Tool]''' | ||
== | ===Kvaser DBC File Editor=== | ||
The File Editor allows the user to modify and create *.dbc files. | |||
'''[http://www. | :'''[http://www.kvaser.com/software/7330130980860/V3_1_879/kvaser_database_editor_setup.exe Kvaser DBC File Editor]''' | ||
Latest revision as of 14:21, 24 February 2023
CCP Master Blocks for MotoHawk
Beta release of the CCP Master Blocks for MotoHawk, supporting MATLAB 6.5.1 through MATLAB R2008a
Requirements: MotoHawk 2008a or later, .NET 2.0 Framework
MotoTron Other Documents
Programming and Development Wiring Harness
SmartCraft 4- and 6-Port Hub Wiring
Hard Boot Recovery
3D CAD Models
KAntrak Software
Free Software Tools
MotoHawk Scanner
The MotoHawk Scanner is a useful tool when you have to work with a module with unknown programming. Instead of guessing the city ID until finding one that works or using a boot key to reflash the module, you can just use the MotoHawk Scanner to determine which city ID the module is on, then interact with it in MotoService or MotoTune using that city ID.
To use this tool, make sure the following are completed:
- The Kvaser CAN-to-USB hardware is plugged into your PC, and your PC recognizes the hardware.
- The CAN network has a proper termination resistor between the two CAN lines (120Ω).
- The controller is turned on (battery power and/or key switch) and has proper CAN connection.
When using MotoHawk Scanner make sure no other programs are using the CAN bus, for example Mototune or Kvaser CANKing. If another program besides MotoHawk Scanner is on the bus, the scanner might not work.
Kvaser DBC File Editor
The File Editor allows the user to modify and create *.dbc files.