Extra Resources and Free Software Tools: Difference between revisions

Latest revision as of 14:21, 24 February 2023

CCP Master Blocks for MotoHawk

CCP Master Blocks for MotoHawk Version 1.0.0 Beta 6

Beta release of the CCP Master Blocks for MotoHawk, supporting MATLAB 6.5.1 through MATLAB R2008a

Requirements: MotoHawk 2008a or later, .NET 2.0 Framework

MotoTron Other Documents

Programming and Development Wiring Harness

112 Quick Programming Harness

112 Development Harness

SmartCraft 4- and 6-Port Hub Wiring

Junction Box Pin Out

Junction Box Wiring

Junction Box Internal Circuitry

Hard Boot Recovery

Hard Boot Recovery Procedure for 48-Pin Modules

3D CAD Models

ECM24 3D Model

ECM48 3D Model

ECM112 3D Model

ECM128 3D Model

KAntrak Software

CCDM PC Tool Installer

Free Software Tools

MotoHawk Scanner

The MotoHawk Scanner is a useful tool when you have to work with a module with unknown programming. Instead of guessing the city ID until finding one that works or using a boot key to reflash the module, you can just use the MotoHawk Scanner to determine which city ID the module is on, then interact with it in MotoService or MotoTune using that city ID.

To use this tool, make sure the following are completed:

The Kvaser CAN-to-USB hardware is plugged into your PC, and your PC recognizes the hardware.
The CAN network has a proper termination resistor between the two CAN lines (120Ω).
The controller is turned on (battery power and/or key switch) and has proper CAN connection.

When using MotoHawk Scanner make sure no other programs are using the CAN bus, for example Mototune or Kvaser CANKing. If another program besides MotoHawk Scanner is on the bus, the scanner might not work.

MotoHawk Scanner Tool

Kvaser DBC File Editor

The File Editor allows the user to modify and create *.dbc files.

Kvaser DBC File Editor

@@ Line 1: / Line 1: @@
-==Engine Control Demo==
+==CCP Master Blocks for MotoHawk==
-:*[http://www.neweagle.net/support/wiki/docs/Extra_Resources/EngineControlDemo001.zip Engine Control Demo 001]
+:'''[http://www.neweagle.net/support/wiki/docs/Other/CANResources/CCPBlockset/CCPBlockset.zip CCP Master Blocks for MotoHawk Version 1.0.0 Beta 6]'''
-::*Simple Engine Control Example written with MotoHawk/Simulink
+Beta release of the CCP Master Blocks for MotoHawk, supporting MATLAB 6.5.1 through MATLAB R2008a
-::*Requirements: MotoHawk
+Requirements: MotoHawk 2008a or later, .NET 2.0 Framework
+==MotoTron Other Documents==
+=== Programming and Development Wiring Harness ===
+: '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/QuickProgrammingHarness112.pdf 112 Quick Programming Harness]'''
+: '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/HARNP112002_Rev03_DevHarness_PCM09xx.pdf 112 Development Harness]'''
+=== SmartCraft 4- and 6-Port Hub Wiring ===
-==CCP Master Blocks for MotoHawk==
+: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/SC_CONN_Pinout.pdf Junction Box Pin Out]'''
-:*[http://www.neweagle.net/support/wiki/docs/Extra_Resources/woodward_custom_ccp_master_1_0_0_beta6 CCP Master Blocks for MotoHawk® version 1.0.0 Beta 6]
+: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_wiring3.jpg Junction Box Wiring]'''
-::*Beta release of the CCP Master Blocks for Motoawk® supporting MATLAB 6.5.1 throught MATLAB R2008a
+: '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_internal2.jpg Junction Box Internal Circuitry]'''
-::*Requirements: MotoHawk 2008a or later, .NET 2.0 Framework
+=== Hard Boot Recovery ===
+: '''[http://www.neweagle.net/support/wiki/docs/Other/48HardBootRecovery/Fire48HardbootRecoveryDocument.pdf Hard Boot Recovery Procedure for 48-Pin Modules]'''
+===3D CAD Models===
+:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM24.ZIP ECM24 3D Model]'''
+:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM48.ZIP ECM48 3D Model]'''
+:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM112.zip ECM112 3D Model]'''
+:'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM128.ZIP ECM128 3D Model]'''
+==KAntrak Software==
+:'''[http://www.neweagle.net/support/wiki/docs/CANtrak/CCDM_PC_Tool_(v1.0.6).msi CCDM PC Tool Installer]'''
+==Free Software Tools==
+===MotoHawk Scanner===
+The MotoHawk Scanner is a useful tool when you have to work with a module with unknown programming. Instead of guessing the city ID until finding one that works or using a boot key to reflash the module, you can just use the MotoHawk Scanner to determine which city ID the module is on, then interact with it in MotoService or MotoTune using that city ID.
+'''To use this tool, make sure the following are completed:'''
+*''The Kvaser CAN-to-USB hardware is plugged into your PC, and your PC recognizes the hardware.''
+*''The CAN network has a proper termination resistor between the two CAN lines (120Ω).''
+*''The controller is turned on (battery power and/or key switch) and has proper CAN connection.''
+When using MotoHawk Scanner make sure no other programs are using the CAN bus, for example Mototune or Kvaser CANKing. If another program besides MotoHawk Scanner is on the bus, the scanner might not work.
+:'''[http://neweagle.net/support/wiki/docs/Extra_Resources/MotoHawk%20Scanner.exe MotoHawk Scanner Tool]'''
+===Kvaser DBC File Editor===
+The File Editor allows the user to modify and create *.dbc files.
+:'''[http://www.kvaser.com/software/7330130980860/V3_1_879/kvaser_database_editor_setup.exe Kvaser DBC File Editor]'''