Extra Resources and Free Software Tools: Difference between revisions
Jump to navigation
Jump to search
| Line 8: | Line 8: | ||
=== Programming and Development Wiring Harness === | === Programming and Development Wiring Harness === | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/QuickProgrammingHarness112.pdf 112 Quick Programming Harness]''' | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/112HarnessSchematics/HARNP112002_Rev03_DevHarness_PCM09xx.pdf 112 Development Harness]''' | ||
=== SmartCraft 4 and 6 port Hub Wiring === | === SmartCraft 4 and 6 port Hub Wiring === | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/SC_CONN_Pinout.pdf JBox Pin Out]''' | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_wiring3.jpg JBox Wiring]''' | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/SmartCraftHub/MotoTron_SmartCraft_10pin_JBOX_internal2.jpg JBox Internal Circuitry]''' | ||
=== Hard Boot Recovery === | === Hard Boot Recovery === | ||
: | : '''[http://www.neweagle.net/support/wiki/docs/Other/48HardBootRecovery/Fire48HardbootRecoveryDocument.pdf Hard Boot Recovery Procedure for 48 pin Modules]''' | ||
===3D CAD Models=== | ===3D CAD Models=== | ||
Requirements: 3D model software | |||
: | :'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM24.ZIP ECM24 3D Model]''' | ||
: | :'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM48.ZIP ECM48 3D Model]''' | ||
: | :'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM112.zip ECM112 3D Model]''' | ||
: | :'''[http://www.neweagle.net/support/wiki/docs/3D_Models/ECM128.ZIP ECM128 3D Model]''' | ||
==KAntrak Software== | ==KAntrak Software== | ||
Revision as of 20:03, 23 February 2023
CCP Master Blocks for MotoHawk
- Beta release of the CCP Master Blocks for MotoHawk, supporting MATLAB 6.5.1 through MATLAB R2008a
- Requirements: MotoHawk 2008a or later, .NET 2.0 Framework
MotoTron Other Documents
Programming and Development Wiring Harness
SmartCraft 4 and 6 port Hub Wiring
Hard Boot Recovery
3D CAD Models
Requirements: 3D model software
KAntrak Software
CCDM PC Tool Installer
Free Software Tools
MotoHawk Scanner
The MotoHawk Scanner is a useful tool when you have to work with a module with unknown programming. Instead of guessing the city ID until finding one that works, or using a boot key to reflash the module, you can just use the MotoHawk Scanner to determine which city ID the module is on, and then interact with it in MotoService or MotoTune by that city ID.
To use this tool, make sure the following are completed:
- The Kvaser CAN-to-USB hardware is plugged into your PC, and your PC recognizes the hardware
- The CAN network has a proper termination resistor between the two CAN lines (120 ohms)
- The controller is turned on (battery power and/or key switch) and has proper CAN connection
When using MotoHawk Scanner make sure no other programs are using the CAN bus, for example Mototune or Kvaser Can King. If another program besides MotoHawk scanner is on the bus, the scanner might not work.
DBC File Editor
The File Editor allows the user to modify and create .dbc files.