MotoHawk-Module-Harnesses-and-Connectors: Difference between revisions
Line 124: | Line 124: | ||
|} | |} | ||
=48- | =48-Pin MotoHawk Module= | ||
==48- | ==48-Pin Module Connectors== | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 148: | Line 148: | ||
|- | |- | ||
|[[File:Con-feml-001a-00-e.jpg|150px]] | |[[File:Con-feml-001a-00-e.jpg|150px]] | ||
|24- | |24-Channel Connector (A Key) | ||
|CON-FEML-001A-00 | |CON-FEML-001A-00 | ||
| | | | ||
Line 154: | Line 154: | ||
|- | |- | ||
|[[File:Con-feml-001a-00-e.jpg|150px]] | |[[File:Con-feml-001a-00-e.jpg|150px]] | ||
|24- | |24-Channel Connector (B Key) | ||
|CON-FEML-001B-00 | |CON-FEML-001B-00 | ||
| | | | ||
Line 171: | Line 171: | ||
|} | |} | ||
==48- | ==48-Pin Module Pigtail Harnesses== | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 186: | Line 186: | ||
|} | |} | ||
==48- | ==48-Pin Module Programming and Boot Harnesses== | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 215: | Line 215: | ||
|} | |} | ||
==48- | ==48-Pin Module Development Harnesses== | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 239: | Line 239: | ||
|} | |} | ||
==48- | ==48-Pin Simulator Harnesses== | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 249: | Line 249: | ||
|- | |- | ||
|[[File:HARN-INTR-024B.jpg|150px]] | |[[File:HARN-INTR-024B.jpg|150px]] | ||
|Simulator Harness for 48 Pin ECM | |Simulator Harness for 48-Pin ECM | ||
Simulator Harness for 48 Pin GCM/HCM | Simulator Harness for 48-Pin GCM/HCM | ||
|HARN-INTR-024B | |HARN-INTR-024B | ||
HARN-INTR-024C | HARN-INTR-024C |
Revision as of 20:34, 26 January 2023
Introduction- Pigtail Harness: A pigtail harness consists of the connectors for the ECM and a wire for each pin on the ECM. - Development Harness: Development Harnesses are pigtail harness's with power, ground, key switch and communication wired. The harness is also covered in loom. - Boot Harness: A boot harness is used when the module has been flashed with bad software and will not respond to attempts to program it. The boot harness will cause the module to go into boot mode and a new programing file flashed onto the module. - Programming Harness: - Simulator Harness: Simulator Harnesses are used in conjunction with a Desk Top Simulator. 24-Pin MotoHawk Module24-Pin Module ConnectorsPlease note that cavity plugs are not used on the connector kits. Overview of 24-pin Connector
24-Pin Module Pigtail Harnesses
24-Pin Module Programming and Boot Harnesses
48-Pin MotoHawk Module48-Pin Module Connectors
48-Pin Module Pigtail Harnesses
48-Pin Module Programming and Boot Harnesses
48-Pin Module Development Harnesses
48-Pin Simulator Harnesses
70-pin MotoHawk Module70-pin Module Connectors
70-pin Module Harnesses
80-pin MotoHawk Module80-pin Module Connectors
80-pin Harnesses
112-pin MotoHawk Module112-pin Module Connectors
112-pin Harnesses
128-pin MotoHawk Module128-pin Module Connectors
128-pin Harnesses
Mounting Hardware
Boot Cable Harnesses, Connectors and KeysBOOT KEY FOR ECM555-48/80 GCM563-48 HCM563-48 ECM565-128 AND ECM5554-112
Connector Crimp and Removal ToolsHAND CRIMP TOOL FOR SMART CRAFT AND 24 PIN MODULES
REMOVAL TOOL - SMARTCRAFT TPA
REMOVAL TOOL - SMARTCRAFT TERMINALS
CRIMP TOOL FOR 48/80/128 PIN ECM PINS
EXTRACTION TOOL FOR 48/80/128 ECM PINS
CRIMPER FOR RELAY TERMINALS
CRIMPER - SMARTCRAFT TERMINALS
CRIMPER - DEUTSCH HDT48-00
CRIMPER 1.5MM FOR 112 PIN ECM CONNECTORS
TERMINAL REMOVAL TOOL - MOLEX 1.5MM FOR 112 PIN CONTROLLER
CRIMPER - MOLEX LARGE TERMINAL ECM70 18-20 AWG
CRIMPER, MOLEX (LARGE) ECM70 TERMINAL, 14-16 AWG
TERMINAL REMOVAL FOR ECM70
REMOVAL TOOL - CM0711 & CM3626 MODULES
REMOVAL TOOL 48 / 80 / 128
REMOVAL TOOL - CM2115 MODULES
CRIMPER TOOL - VEECAN DISPLAYS
|