MotoHawk-Module-Harnesses-and-Connectors: Difference between revisions
Line 892: | Line 892: | ||
'''CRIMPER - MOLEX . | '''CRIMPER - MOLEX 0.63MM FOR 112-PIN CONTROLLER CONNECTORS''' | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 903: | Line 903: | ||
[[File:Image 580.jpg|150px]] | [[File:Image 580.jpg|150px]] | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
Crimp Tool for Matte . | Crimp Tool for Matte 0.63mm Molex Terminals | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
TOOL-CON-016-MATTE (TOOL-GCM48-01) | TOOL-CON-016-MATTE (TOOL-GCM48-01) | ||
Line 913: | Line 913: | ||
'''CRIMPER 1. | '''CRIMPER 1.5MM FOR 112-PIN ECM CONNECTORS''' | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 924: | Line 924: | ||
[[File:Image 581.jpg|150px]] | [[File:Image 581.jpg|150px]] | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
Crimp Tool for 1. | Crimp Tool for 1.5mm Molex Matte Terminals | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
TOOL-CON-017-MATTE (TOOL-GCM48-02) | TOOL-CON-017-MATTE (TOOL-GCM48-02) | ||
Line 933: | Line 933: | ||
'''TERMINAL REMOVAL TOOL - MOLEX 0. | '''TERMINAL REMOVAL TOOL - MOLEX 0.63MM FOR 112-PIN CONTROLLER CONNECTORS''' | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 944: | Line 944: | ||
[[File:Tool-con-018-matte.jpg|150px]] | [[File:Tool-con-018-matte.jpg|150px]] | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
Removal Tool for . | Removal Tool for 0.63mm Molex Matte Terminals | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
TOOL-CON-018 | TOOL-CON-018 | ||
Line 952: | Line 952: | ||
|} | |} | ||
'''TERMINAL REMOVAL TOOL - MOLEX 1. | '''TERMINAL REMOVAL TOOL - MOLEX 1.5MM FOR 112-PIN CONTROLLER''' | ||
{| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | {| class="wikitable" style="text-align: center; width:850px" cellpadding = "5" | ||
Line 964: | Line 964: | ||
[[File:Image 585.jpg|150px]] | [[File:Image 585.jpg|150px]] | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
Removal Tool for 1. | Removal Tool for 1.5mm Molex Terminals | ||
|style = "height:180px; width:180px;"| | |style = "height:180px; width:180px;"| | ||
TOOL-CON-019 | TOOL-CON-019 |
Revision as of 15:37, 6 February 2023
Introduction- Pigtail Harness: A pigtail harness consists of the connectors for the ECM and a wire for each pin on the ECM. - Development Harness: Development harnesses are pigtail harnesses with power, ground, key-switch and communication wired. The harness is also covered in loom. - Boot Harness: A boot harness is used when the module has been flashed with bad software and will not respond to attempts to program it. The boot harness will cause the module to go into boot mode and a new programing file will be flashed onto the module. - Programming Harness: A programming harness contains only the necessary connections to communicate with and flash the module. This includes Battery, Ground, Wake_Input1 (KeySW), and CAN1+/-. - Simulator Harness: Simulator harnesses are used in conjunction with a Desk Top Simulator. 24-Pin MotoHawk Module24-Pin Module ConnectorsPlease note that cavity plugs are not used on the connector kits. Overview of 24-Pin Connector
24-Pin Module Pigtail Harnesses
24-Pin Module Programming and Boot Harnesses
48-Pin MotoHawk Module48-Pin Module Connectors
48-Pin Module Pigtail Harnesses
48-Pin Module Programming and Boot Harnesses
48-Pin Module Development Harnesses
48-Pin Simulator Harnesses
70-Pin MotoHawk Module70-Pin Module Connectors
70-Pin Module Harnesses
80-Pin MotoHawk Module80-Pin Module Connectors
80-Pin Harnesses
112-Pin MotoHawk Module112-Pin Module Connectors
112-Pin Harnesses
128-Pin MotoHawk Module128-Pin Module Connectors
128-Pin Harnesses
Mounting Hardware
Boot Cable Harnesses, Connectors and KeysBOOT KEY FOR ECM555-48/80, GCM563-48, HCM563-48, ECM565-128 AND ECM5554-112
Connector Crimp and Removal ToolsHAND CRIMP TOOL FOR SMARTCRAFT AND 24-PIN MODULES
REMOVAL TOOL - SMARTCRAFT TPA
REMOVAL TOOL - SMARTCRAFT TERMINALS
CRIMP TOOL FOR 48/80/128-PIN ECM PINS
EXTRACTION TOOL FOR 48/80/128 ECM PINS
CRIMPER FOR RELAY TERMINALS
CRIMPER - SMARTCRAFT TERMINALS
CRIMPER - DEUTSCH HDT48-00
CRIMPER 1.5MM FOR 112-PIN ECM CONNECTORS
TERMINAL REMOVAL TOOL - MOLEX 1.5MM FOR 112-PIN CONTROLLER
CRIMPER - MOLEX LARGE TERMINAL ECM70 18-20AWG
CRIMPER, MOLEX (LARGE) ECM70 TERMINAL, 14-16AWG
TERMINAL REMOVAL FOR ECM 70
REMOVAL TOOL - CM 0711 and CM 3626 MODULES
REMOVAL TOOL 48/80/128
REMOVAL TOOL - CM 2115 MODULES
CRIMPER TOOL - VEECAN DISPLAYS
|