GCM70: Difference between revisions

From NewEagleWiki
Jump to navigation Jump to search
No edit summary
Line 7: Line 7:


==Variants==
==Variants==
:'''GCM-5634M-70-1459'''
 
:'''GCM-5634M-70-1559'''
:'''GCM-5634M-70-1559'''
:'''GCM-5634M-70-1562'''
:'''GCM-5634M-70-1562'''


==Datasheets==
==Datasheets==
*'''GCM-5634M-70-1459'''
:'''[https://www.neweagle.net/support/wiki/ProductDocumentation/Raptor/Controllers/GCM-5634M-070-1459_DataSheet.pdf Datasheet]'''


*'''GCM-5634M-70-1559'''
*'''GCM-5634M-70-1559'''
Line 20: Line 18:
*'''GCM-5634M-70-1562'''
*'''GCM-5634M-70-1562'''
:'''[https://www.neweagle.net/support/wiki/ProductDocumentation/Raptor/Controllers/GCM-5634M-070-1562_DataSheet.pdf Datasheet]'''
:'''[https://www.neweagle.net/support/wiki/ProductDocumentation/Raptor/Controllers/GCM-5634M-070-1562_DataSheet.pdf Datasheet]'''
==Obsolete==
The GCM-5634M-70-1459 is end of life and is considered obsolete.
:'''GCM-5634M-70-1459'''
:'''[https://www.neweagle.net/support/wiki/ProductDocumentation/Raptor/Controllers/GCM-5634M-070-1459_DataSheet.pdf Datasheet]'''


==Pins and Crimping==
==Pins and Crimping==

Revision as of 18:15, 27 January 2021

Raptor GCM70

The GCM70 is a general purpose control module. The module has 2 CAN buses, and sports a 3-phase motor driver. The eclectic inputs and outputs make this module suitable for a wide variety of general purpose applications.

The GCM70 is part of a family of rugged, automotive-grade production controllers that use a software development process based on MATLAB/Simulink, known as Raptor-Dev. Raptor-Dev significantly speeds up algorithm development by using automatic code generation. In addition, developers can quickly test application software on their PCs with a built-in onscreen PC simulation.

Variants

GCM-5634M-70-1559
GCM-5634M-70-1562

Datasheets

  • GCM-5634M-70-1559
Datasheet
  • GCM-5634M-70-1562
Datasheet

Obsolete

The GCM-5634M-70-1459 is end of life and is considered obsolete.

GCM-5634M-70-1459
Datasheet

Pins and Crimping

Need to make a harness? Click here to get started.

Want to buy a pre-made harness? Click here to order.


Compiler

GCC PowerPC EABI 4.6.0 SPE

Download Now


FAQ

Non-Volatile Memory Corruption

Non-Volatile memory can be corrupted during a write if the module is improperly powered off (ie removing power from Batt+ (Pin 68)).

Calibrations

In production programs, it is recommended to store all calibrations in Flash memory (available within the "raptor_target_def" block).

Recovery Procedure (Boot Key)

The GCM70 requires a Boot Key to recover the module. These can be found on our store page

The use the boot key to recover the malfunctioned module, please follow the Raptor-Cal MotoHawk Module Recovery steps provided: Boot Key Recovery and below.

Notes:
The Boot Key signal (Pin E on the Smartcraft connector) needs to be connected to the SWG4 pin for the GCM70.
Once the bootkey is used, the module will default to a CAN baud rate of 250k, so update the Raptor-Cal settings accordingly.

Power Cycle Instructions:

  • Step 1: Remove all power to the module by turning off Key switch and then power supply. Connect the Boot Key to the bus.
  • Step 2: From Raptor-CAL/Service: Select Program, then the recover check box, MotoHawk, Select the .RPG file.
  • Step 3: Click OK, turn on power supply, then key switch.

For a full list of steps, see the Raptor-CAL FAQ Page

Bootstrap

The GCM70 can be forced to remain in the firmware bootloader by applying a bootstrap sequence. The bootstrap sequence is:

  Pin       State for Boot
  AN1   High
  AN2   High
  AN3   High
  AN4
  AN5
  AN6
  AN7
  AN8
  AN9   Low
  AN10   Low
  AN11   Low

Raptor™ GCM 70 Power Up Process

Raptor™ GCM 70 Power Up Process, a product review and development tutorial.

Difference Between 1459 and 1559 variants

Pins 39, 40, 41, 59, & 60 have different pull-up resistors

SPD1 Limit

The frequency speed limit in the SPD1 resource is designed for 10K.