IO Devices

System Input/Output Modules (IO)

J1772 Vehicle Power Interface Module (VPIM)

The J1772 Vehicle Power Interface Module (VPIM) provides the necessary circuitry to interface with Electric or plug-in Hybrid Electric vehicle charging equipment in accordance with the SAE J1772 specifications. It allows the vehicle systems and ECUs that require a low current "sleep" mode to be managed externally and monitors the inputs, providing an output that will drive an external "Wake Up" relay which, in turn, provides power to the connected systems.

Features include:

• Operating Voltage: 8-30 VDC
• J1772 Hardware Interface
• Low Current Consumption < 10mA
• Operating Temperatures ranging from -40°C to 105°C

Part Number	Picture	Visit our Webstore	Datasheets	More Information
VPIM-012-1201		J1772 Interfave Module	Vehicle Power Interface Module Datasheet	For more information, refer to the J1772 Sleep Manager section on our Electric Vehicles page.

Multiplexed Power Distribution Module (MPDM)

The New Eagle™ Multiplexed Power Distribution Module offers economical CAN Network oversight for high power circuits in vehicle power distribution. Manufactured as a hardened and weather tight module, it may be configured to provide various OEM circuit protection and switching functions, using industry standard fuses, relays and breakers, with the status and control of each circuit accessible through J1939/CAN open messages.

General Features:

• Operating Voltage - 9 to 32 Volts
• Max Current Capacity - 200 Amps
• Max Current Capacity per pin - 30 Amps
• Operating Temperature - -40 C to +85 C
• Ingress Protection - IP66 Equivalent
• CAN Baud rate - 250kbps
• Multiple Modules Will Work on a Single CAN Bus

Part Number	Picture	Visit our Webstore	Datasheets	More Information
MPDM-NE1	An open Multiplexed Power Distribution Module A closed Multiplexed Power Distribution Module	Multiplexed Power Distribution Module	Multiplexed Power Distribution Module Datasheet Multiplexed Power Distribution Module User Manual MPDM CAD File	Multiplexed Power Distribution Module

New Eagle H-bridge Driver

The New Eagle H-Bridge driver is an external driver circuit designed to allow additional high current H-Bridge outputs to be added to a control module. The H-Bridge driver incorporates internal protection for over current, over temperature and reverse battery protection. Current sense and diagnostic outputs allow the controller to monitor operation and detect if the driver has gone into a protection shutdown state. The H-Bridge driver requires 2-4 outputs and 0-2 inputs to properly operate from the control module. Built in pullup resistors in the driver allow the H-Bridge driver to be operated from either logic type EST outputs or low side drivers.

Part Number	Picture	Visit our Webstore	Datasheets	More Information
Coming Soon		Coming Soon	New Eagle H-Bridge Driver Datasheet	H-Bridge Driver

Digital to Analog Converter

This New Eagle module receives a PWM signal from a MotoHawk PWM output, and can convert into a pure analog, 0-5 volt output. Single or multiple channels are available. The module is designed to give you the ability to simulate a digital, single potentiometer, or dual potentiometer. There is an internal override/safety pulse input that you can enable/disable in order to pass through the original signal or the simulated signal. The potentiometer signals are generated using an external low-side drive between 4-10Khz. The incoming signal should be be low side driven because there is an internal 5V pull-up resistor. For more information refer to the datasheet PWM to Analog datasheet.

Part Number	Picture	Visit our Webstore	Datasheet	More Information
PWM-EST-24-1182	File:PWM to Analog Converter.jpg	PWM to Analog Converter	New Eagle Sensors to CAN Module Datasheet	PWM to Analog Converter

Vehicle Control Modules (VCM)

Part Number	Picture	Visit our Webstore	Datasheet	More Information
KCIM Module		Webstore: KAntrak Configurable Input Module	VCM datasheets KCIM Manual	KAntrak Configurable Interface Module

Operator Input Devices

Electronic Foot Pedals

New Eagle sells electronic foot pedals that could be used as accelerator or brake pedals for your vehicle. The pedals have dual potentiometers that source power from 2 independent power supplies and output voltages between 0 & 5 V and 0 & 2.5 V. We also sell a connector kit for developing a harness that fits your needs. We have both firewall and floor mounted models.

Voltage Supply

For proper use the pedals should be supplied with a 5V power supply. When the voltage is above the 15V the pedals can become permantly damaged.

When using these pedals with a MotoHawk module use the 5V XDRP sensor supply output to provide power to the foot pedal. Also, use the XDRDG sensor ground to ground the pedal. This is a clean ground that helps provide a more accurate reading.

Electronic Foot Pedal - Floor Mounted

Part Number	Picture	Visit our Webstore	Datasheets
EFP-136-01	Floor Mounted	Electronic Foot Pedal - Floor	Floor Mounted Electronic Foot Pedal Datasheet

Electronic Foot Pedal - Firewall Mounted

Part Number	Picture	Visit our Webstore	Datasheets
EFP-139-00	Firewall Mounted	Electronic Foot Pedal - Firewall	Firewall Mounted Electronic Foot Pedal Datasheet

Electronic Throttle Cable

The EVR-001 provides engine speed adjustment on electronically controlled stationary engines or from a remote operating position on mobile equipment. the large (2-1/4") knob provides continuous engine speed regulation from idle to wide open in seven full turns. the EVR-001 is easily installed in limited space.

Part Number	Picture	Visit our Webstore	Datasheets
EVR-001		Webstore: EVR-001	EVR-001 Datasheet

Digital Keypads

8 Position Keypad

This standard keypad allows a designer to build a semi-custom system for a minimal cost. Each keypad is made from extremely high-quality and rugged silicone that can be laser etched with specified button legends, text or company logos. Reconfigurable, re-addressable, and relegedable. This keypad is the ultimate interface device. This flexible, smart, and rugged family of keypads offers endless applications and configurations to meet the needs of any industry. The 8 Position keypad offers eight backlit buttons configurable to various applications. Communication protocols include RS485, J1030/J1939-11, CAN-Open and others.

Part Number	Picture	Visit our Webstore	Data
KEYPAD-DS-008-00		New Eagle 8 Position CAN Keypad	8 Position Keypad datasheet

11 Switch Keypad

The 11 switch keypads are versatile designs which are compatible with the full range of New Eagle multiplex control modules. This allows a complete system or subsystem in wide range CAN based vehicles and applications to be quickly and easily created. Alternatively the keypad can simply be incorporated into a vehicle's existing CAN bus. Its generic slave configuration, which is common to many CAN based applications, allows the vehicle application to take full control of the keypad and give each switch its own characteristics. Click here for more information

Part Number	Picture	Visit our Webstore	Data
KEYPAD-011-00		New Eagle 11 Switch Keypad	N/A

6 Switch Keypad

The 6 switch keypad is a highly versatile design which is compatible with the full range of Megalink™ multiplex control modules. This allows a complete system or subsytem in wide range CAN based vehicles and applications to be quickly and easily created. Alternatively the keypad can simply be incorporated into an existing CANbus network. Its generic slave configuration, which is common to many CAN based applications, allows the vehicle application to take full control of the keypad and give each switch its own characteristics.

Part Number	Picture	Visit our Webstore	Data
KEYPAD-011-00		Please Contact Sales for purchase info	N/A